Electrocution Protection Fire Retardent LonMat UV Vinyl Rolls 3 x 75Ft

Top Features for LonMat UV Vinyl Rolls 3 x 75 Ft

1. Electrocution protection
2. Used by the Military and NATO
3. Meet MIL-DTL-15562G, Type I specifications
4. Fire retardant
5. Long lasting marbleized surface
6. UV cured finish
7. Easy to maintain
8. 3 ft width

LonMat® UV meets the U. S. Military and NATO Switchboard Matting, MIL-DTL-15562G, TYPE I specifications for flooring mat products that protect workers from electrocution by disrupting the route to ground. Type I Switchboard Mats are often used on ship decking and by electrified equipment when maintenance and operations personnel are working. They are known for their water-tight integrity with heat-welded seams. The flooring rolls offer the look of luxury while offering a level of safety.

LonMat® UV marble sheet vinyl flooring roll features an advanced UV-cured urethane finish that eases maintenance. This long-lasting, marbleized, fire-retardant, electrically-insulating surface has been used by countless naval vessels' high-voltage areas for decades. The LonMat® UV marble vinyl flooring roll meets the U. S. Military and NATO Switchboard Matting, MIL-DTL-15562G, TYPE I specifications for flooring mat products that protect workers from electrocution by disturbing the path to ground.

LonMat® Marble Vinyl Flooring Roll - Specs & Options

The LonMat Lonseal flooring comes in rolls that are 3 feet wide and 75 feet in length. They have an overall thickness of 3.2 millimeters and a wear layer thickness of 1.2 millimeters. Each roll is 240 pounds. This attractive, marble patterned floor with a smooth finish comes in grey marble, blue marble, beige marble, and green marble.

This LonMat marble vinyl flooring roll meets MIL-DTL-15562G, Type II, and features a GreenAir® (low VOC) formulation. This product is one of the finest quality, eco-conscious products available with little effects on the environment. It meets the highest industry standards in manufacturing and distribution. It’s made by an environmentally-conscious manufacturer and provides the most functional, sustainable, and durable military specialty flooring products available. It has the lowest VOC properties of any vinyl flooring product on the market.

LonMat® Marble Vinyl Flooring Roll - Installation Method

1. Make relief cuts as necessary to fit the floor to the installation area.


2. If required, apply Lonseal DFT at seam locations.


3. For simple rooms or installations, select the sheet nearest the wall or perimeter and tube (gently fold the flooring over itself lengthwise) towards the center of the room. Take care, and keep the radius large when tubing the material. Failure to do so could result in damage to the flooring, and visual imperfections may appear on the surface.


4. Spread the appropriate adhesive over the substrate, and after sufficient open time, roll the flooring into the adhesive.


5. After anchoring the first section down, tube the other half of the sheet, and the adjacent sheet, if present. Spread the adhesive over the substrate and seam location, including any DFT. After sufficient open time, roll the flooring into the adhesive, removing the DFT liner beforehand.


6. Continue until the entire area is fully adhered.


7. Trim seams if necessary, and roll the flooring securely into the adhesive or DFT with a hand roller.


8. Heat or chemical weld the seams. Do not heat weld seams less than 24 hours after installation, unless DFT was used.

LonMat® Marble Vinyl Flooring Roll - Cleaning & Maintenance

To ensure the quality and integrity of the floor is maintained, it is imperative that the maintenance method is used.

Initial Maintenance:

1. Ensure the proper installation method has been followed


2. Always wait 48 hours after installation has been completed before beginning initial maintenance.


3. Clean the flooring using a microfiber dust mop. If necessary, vacuum the floor to first pick up any large particles.


4. Using a properly diluted neutral pH cleaner, scrub the floor with a TASKI Contact Pad on a slow speed (175 – 300 RPM) rotary floor machine or auto-scrubber, vacuuming up any remaining cleaning solution. 5. If necessary, use clean water and a clean microfiber mop pad to remove any remaining residue.

Routine/Daily Maintenance:

1. Remove all gross soiling (food, gum, residues, etc.). Take care if using a scraper or putty knife to avoid permanently damaging the surface of the flooring.


2. Clean the flooring using a microfiber dust mop. If necessary, vacuum the floor to first pick up any large particles.


3. Apply a properly diluted neutral cleaner to the surface using a microfiber wet mop pad.


4. If necessary, use clean water and a clean microfiber mop pad to remove any remaining residue.

Periodic Maintenance:

1. Remove all gross soiling (food, gum, residues, etc.). Take care if using a scraper or putty knife to avoid permanently damaging the surface of the flooring.


2. Clean the flooring using a microfiber dust mop. If necessary, vacuum the floor to first pick up any large particles.


3. Using a properly diluted neutral pH cleaner, scrub the floor with a red buffing pad on a slow speed (175 – 300 RPM) rotary floor machine or auto-scrubber, vacuuming up any remaining cleaning solution. If intending to revitalize the gloss of the floor, substitute a spray buff for the neutral pH cleaner.


4. If necessary, use clean water and a clean microfiber mop pad to remove any remaining residue.

LonMat® by LonSeal® - The Best Military Flooring Solution

This top notch, commercial grade military flooring solution is a high performing, appealing solution that is suitable for so many applications. For more information, reach out to the customer service team at Greatmats. They can answer your questions and offer assistance placing your order.


FEATURES (data shown is nominal):
Roll size 3': 3 ft. (0.9 m) wide x 75' (22.9 m) length
Overall Thickness: 0.128 in. (3.2 mm)
Wear Layer Thickness: 0.048 in. (1.2 mm)
Weight: 1.1 lbs./sq. ft. (5.1 kg/m²)

MEETS MIL-DTL-15562G, Type I

Pattern: Marbled
Finish: Smooth
Width: 3 ft. (36 in.) (0.9 m)

Green Specs: MIL-DTL-15562G

Shipping

Ships via freight delivery

This Product Ships Freight Only.
Please review ourshipping disclaimer.

Ask a question

PDF Documents:

• View Installation Instructions
• View Cleaning and Maintenance
• View Specifications Data Sheet
• View Recommended Maintenance Products